Lincoln 1997 Town Car Owner'S Manual Download Page 129 | Manualshive

Page: 129 / 305

background image

125

WARNING

It is extremely dangerous to ride in a
cargo area, inside or outside of a
vehicle. In a collision, people riding in
these areas are more likely to be
seriously injured or killed. Do not
allow people to ride in any area of your
vehicle that is not equipped with seats
and safety belts. Be sure everyone in
your vehicle is in a seat and using a
safety belt properly.

WARNING

Always drive and ride with your
seatback upright and the lap belt snug
and low across the hips.

WARNING

Each seating position in your vehicle
has a specific safety belt assembly
which is made up of one buckle and
one tongue that are designed to be used
as a pair. 1) Use the shoulder belt on
the outside shoulder only. Never wear
the shoulder belt under the arm. 2)
Never swing it around your neck over
the inside shoulder. 3) Never use a
single belt for more than one person.

File:06fnsst.ex

Update:Fri Jun 21 08:57:53 1996

«
...
127
128
129
130
131
...
»

Summary of Contents for 1997 Town Car


















































































































































































































































































































Reviews:

No comments

Related manuals for 1997 Town Car

Brand: Valeo Pages: 17

Brand: OEM Tools Pages: 4

Brand: Triumph Pages: 86

Brand: Vauxhall Pages: 323

Brand: Whispbar Pages: 15

Brand: Curt Manufacturing Pages: 6

Brand: U & Me Brothers Pages: 6

Brand: AA Products Pages: 4

VIEWLINE 52 MM - MOUNTING 11-09

Brand: VDO Pages: 4

Brand: Metra Electronics Pages: 8

Sedan CIVIC 2022

Brand: Honda Pages: 701

Brand: HAKR Pages: 9

Brand: Volvo Pages: 18

Brand: Master Tailgaters Pages: 10

Charger SRT 392 2017

Brand: Dodge Pages: 576

Brand: Lexus Pages: 108

Brand: Belkin Pages: 30

Brand: Mitsubishi Pages: 141

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands