Lincoln 1997 Town Car Owner'S Manual Download Page 137 | Manualshive

Page: 137 / 305

background image

133

To fasten a cinch tongue, pull the combination lap
and shoulder belt from the retractor so that the
shoulder belt portion of the safety belt crosses your
shoulder and chest. Be sure the belt is not twisted.
If the belt is twisted remove the twist. Insert the
belt tongue into the proper buckle for your seating
position until you hear a snap and feel it latch.
Make sure the tongue is securely fastened to the
buckle by pulling on the tongue.

WARNING

The lap belts should fit snugly and as
low as possible around the hips, not
around the waist.

WARNING

Front and rear seat occupants, including
pregnant women, should wear safety
belts for optimum protection in an
accident.

WARNING

Each seating position in your vehicle
has a specific safety belt assembly
which is made up of one buckle and
one tongue that are designed to be used
as a pair. 1) Use the shoulder belt on
the outside shoulder only. Never wear
the shoulder belt under the arm. 2)
Never swing it around your neck over
the inside shoulder. 3) Never use a
single belt for more than one person.

While you are fastened in the seat belt, the
combination lap/shoulder belt with a cinch tongue
adjusts to your movement. However, if you brake
hard, turn hard, or if your vehicle receives an
impact of 5 mph (8 km/h) or more, the safety belt
will become locked and help reduce your forward
movement.

File:06fnsst.ex

Update:Fri Jun 21 08:57:53 1996

«
...
135
136
137
138
139
...
»

Summary of Contents for 1997 Town Car


















































































































































































































































































































Reviews:

No comments

Related manuals for 1997 Town Car

Brand: Aries Pages: 3

Brand: iArmor Pages: 6

Brand: GATmatic Pages: 13

Brand: Metra Electronics Pages: 8

Brand: Würth Pages: 36

Brand: tams elektronik Pages: 19

Brand: Bestop Pages: 5

Brand: PowerMadd Pages: 3

Brand: Thule Pages: 12

Brand: Thule Pages: 2

Brand: Car-Interface Pages: 23

Brand: Kuda-Phonebase Pages: 3

Brand: Ranger design Pages: 22

Brand: PMT Pages: 16

Brand: Truma Pages: 16

Brand: Fortin Electronic Systems Pages: 5

Brand: Jeep Pages: 52

Brand: Chevrolet Pages: 426

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands