LG PREMTB100 Owners & Installation Manual Download | Manualshive

Page: 81 / 82

background image

Ventilation Fan Speed Alignment (general ventilator)

It is the function to change the standard fan speed of the ventilation product.

• Select value using [<,>(left/right)] button.

Filter check alarm(general ventilator)

This function sets the filter check alarm of the ventilation product.

• Select value using [<,>(left/right)] button.

Value

Default value

10% increase

10% decrease

20% decrease

Value

Step 0 - 5

ENGLISH

INSTALLER SETTING

160

GUIDE TO DIFFERENT MODE OPERATION/OPEN SOURCE SOFTWARE

161

GUIDE TO DIFFERENT MODE
OPERATION/OPEN SOURCE SOFTWARE

Different mode operation

Different mode operation is the case when the indoor units’ operation modes are different when
multiple indoor units are installed to one outdoor unit. (Different mode operation doesn’t happen
in the cooling exclusive model.)

• Example of different mode operation

- When one indoor unit is operated in heat while several indoor units one outdoor unit are oper-

ated in cooling, the heating operation is not performed.

- With one outdoor unit, while several indoor units are in heat mode, if one indoor unit requests

in cooling or dehumidification, the operation is not performed.

Open Source Software Notice Information

To obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is con-
tained in this product, please visit http://opensource.lge.com. In addition to the source code, all
referred license terms, warranty disclaimers and copyright notices are available for download. LG
Electronics will also provide open source code to you on CD-ROM for a charge covering the cost
of performing such distribution (such as the cost of media, shipping, and handling) upon email re-
quest to [email protected]. This offer is valid for a period of three years after our last ship-
ment of this product. This offer is valid to anyone in receipt of this information.

«
...
79
80
81
82
»

Summary of Contents for PREMTB100



















































































Reviews:

No comments

Related manuals for PREMTB100

MOB30-18HDN1-MQ0W

Brand: ZenAire Pages: 94

SMOKEMASTER C-12

Brand: Air Quality Engineering Pages: 14

Appliances AJCQ10ACDH5

Brand: GE Pages: 16

Sky Air B-Series R-410A

Brand: Daikin Pages: 338

AERAMAX PRO AM3 PC

Brand: Fellowes Pages: 12

Brand: Ohyama Pages: 72

Brand: TCL Pages: 49

Brand: IDEAL Pages: 65

Nexya S4 E Series

Brand: Olimpia splendid Pages: 336

Brand: Technibel Pages: 27

Brand: ALPATEC Pages: 20

Brand: HTW Pages: 76

Brand: Fakir Pages: 56

climaVAIR V 7-050 NW

Brand: Vaillant Pages: 24

Brand: CLIMAVENETA Pages: 68

Twin Temp EQ08J11A

Brand: Friedrich Pages: 40

TRILECTRON AIR-A-PLANE RJ150-30

Brand: Illinois Tool Works Pages: 167

Brand: GE Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands