LG PREMTB100 Owners & Installation Manual Download

Page: 68 / 82

135

INSTALLER SETTING

ENGLISH

134

INSTALLER SETTING

Indoor unit address veriﬁcation (air conditioner / DX ventilator)

This function allows you to check the address of the indoor unit designated by the outdoor unit.

• In the installer setting list, select the indoor unit address check category, and press [OK] button

to move to the detail screen.

Static pressure step setting (air conditioner)

It is the function to subdivide and set the product’s Static pressure to 11 stages.

• Change setting values using [<,>(left/right)] button.

Value

Step 0 ~ Step 11

NOTE

If Static pressure step setting is used, the Static pressure setting is not used.

For the Static pressure step value for each stage, refer to the indoor unit product manual

Summary of Contents for PREMTB100



















































































Search results

Summary of Contents for PREMTB100

Reviews:

Related manuals for PREMTB100

Brands by name

Popular brands

LG PREMTB100, Owners & Installation Manual

Search results

Summary of Contents for PREMTB100

Reviews:

Related manuals for PREMTB100

Brands by name

Popular brands