LG PREMTB100 Owners & Installation Manual Download

Page: 66 / 82

131

INSTALLER SETTING

130

INSTALLER SETTING

ENGLISH

Emergency heater setting (air conditioner)

Enable the emergency heater control function and the usage environment.

• In the installer setting list, select the emergency heater setting category, and press [OK] button

to move to the detail screen.

- In case of an error, it sets whether the emergency heater can be used / outdoor temperature

standard heater operation usage setting and temperature step value setting / and during the
emergency heater operation, whether to use the indoor unit fan operation.

Value

Outdoor temperature standard heater

operation

Fan operation in emergency

control

Not use

Use

Emergency heater

Step 0 ~ 3

On/Off

Extended emer-

gency heater

Step 0 ~ 15

NOTE

This function setting must be carried out by a certified-technician.

Function control during group Control setting (air conditioner)

This function enables the control of the common functions or some functions based on the mas-
ter indoor unit during the group control.

• Change setting values using [<,>(left/right)] button.

Value

Description

Not use

Common function,

Use

Use expanded function which

is based on master indoor unit

NOTE

Common functions and some indoor unit master standard setting shall be set only during
the group control with the same type indoor units.

During the group control with different indoor unit types, set it as ‘000’ to use the existing
group control method.

Summary of Contents for PREMTB100



















































































Search results

Summary of Contents for PREMTB100

Reviews:

Related manuals for PREMTB100

Brands by name

Popular brands

LG PREMTB100, Owners & Installation Manual

Search results

Summary of Contents for PREMTB100

Reviews:

Related manuals for PREMTB100

Brands by name

Popular brands