LG PREMTB100 Owners & Installation Manual Download Page 8

Page: 8 / 82

OPERATION SETTING

ENGLISH

Dry Operation

Dry operation’s initial fan speed is “Low”.

Dry operation does not have a separate desired temperature.

- If you unit is operating in dehumidification mode and you press the [On/Off] button the dehu-

midification operation will shut off.

NOTE

If you use it in the rainy season, or when the humidity is high, you can have both the
effective dehumidification and cooling operation at the same time.

Heating Operation

The heating operation’s minimum setting temperature is 16°C.

For some types of the indoor units, the desired temperature can be controlled in the units of 1°C
or 0.5°C.

- Set the desired temperature higher than the indoor temperature.

- Indoor temperature is displayed on the default screen of the remote controller.

- When the desired temperature is set lower than the indoor temperature, warm air doesn't

come out, but for some products, the fan will recirculate room air, or stop altogether.

- If you unit is operating in heating mode and you press the [On/Off] button the heating operation

will shut off.

NOTE

In the heating operation, you can select the desired temperature in the range of 16°C ~ 30°C.

Heating operation is operated only in cooling/heating model. The heating is not operated in
cooling exclusive model.

Summary of Contents for PREMTB100



















































































Search results

Summary of Contents for PREMTB100

Reviews:

LG PREMTB100, Owners & Installation Manual, Page: 8 / 82

Search results

Summary of Contents for PREMTB100

Reviews: