LG PREMTB100 Owners & Installation Manual Download | Manualshive

Page: 58 / 82

background image

115

INSTALLER SETTING

114

AIR CONDITIONER AND VENTILATION INTERFACE

ENGLISH

AIR CONDITIONER AND VENTILATION IN-
TERFACE

• It controls using the wired remote controller at a place where the air conditioner indoor unit and

the ventilation product are connected and installed at the same time.

- When the power is applied, the remote controller recognizes the product and operates nor-

mally.

※

The wiring method is the same as the air conditioner user manual. (Refer to the remote con-
troller manual group control page contents)

※

Ventilation product means general ventilation product and direct cooling type ventilation prod-
uct.

Independent operation

Interfaced operation

General

ventilation

WIRED
REMOTE
CONTROLLER

General
ventilation

OK

WIRED
REMOTE
CONTROLLER

General
ventilation

Air conditioner
indoor unit

OK

Direct

ventilation

WIRED
REMOTE
CONTROLLER

General
ventilation

OK

WIRED
REMOTE
CONTROLLER

General
ventilation

Air conditioner
indoor unit

OK

[general ventilation

independent operation]

[General ventilation interfaced operation]

[Direct ventilation interfaced operation]

[Direct ventilation

independent operation]

INSTALLER SETTING

How to enter installer setting

• In the menu screen, press [<,>(left/right)] button to select the setting category, and press

[

∧

(up)] button for 3 seconds to enter the password input screen for the installer setting.

• Input the password and press [OK] button to move to the installer setting list.

※

Installer setting password

Main screen

→

menu

→

setting

→

service

→

RMC version information

→

SW Version

Example) SW version : 1.00.1 a

In the above case, the password is 1001.

CAUTION

The installer setting mode is the mode to set the remote controller’s detail function. If the in-
staller setting mode is incorrectly set, it may cause product failure, user’s injury, or property dam-
age. It must be set by the installation specialist with the installation license, and if it is installed or
changed without installation license, all problems caused will be the responsibility of the installer,
and may void the LG warranty.

!

OK

OK

NOTE

!

Some categories of the installer setting menu may not be available depending on the
product function or the menu name may be different.

«
...
56
57
58
59
60
...
»

Summary of Contents for PREMTB100



















































































Reviews:

No comments

Related manuals for PREMTB100

Brand: Panasonic Pages: 18

Brand: Unitary products group Pages: 16

WI-CH2010-WSDC2-W-APS-INV

Brand: Saijo Denki Pages: 10

Brand: Daewoo Pages: 131

Brand: York Pages: 44

Brand: Taurus Alpatec Pages: 180

Brand: AERMEC Pages: 48

Brand: EAS Electric Pages: 199

Brand: Zamil Pages: 51

Brand: Goodman Pages: 48

13 SEER TCGD12 - 60 SERIES

Brand: Unitary products group Pages: 12

RKHBH016AB Series

Brand: Rotex Pages: 72

Brand: Ryobishi Pages: 24

Brand: Air-Care Pages: 6

Brand: REMEZA Pages: 29

Brand: Indel B Pages: 100

Brand: Daikin Pages: 20

Brand: Daikin Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands