LG PREMTB100, Owners & Installation Manual

Page: 59 / 82

117
INSTALLER SETTING
116
INSTALLER SETTING
ENGLISH
Installer setting – air conditioner
• You can set the product user functions.
• Some functions may not be displayed/operated in some product types.
Menu Description
Test run setting
It is the function to set the trial operation at the initial product installa-
tion.
Central control address
Setting
It is the function to set the central control address of the indoor unit
during the central controller connection.
ESP setting
It is the function to set the wind amount value corresponding to each
wind amount for easy installation.
Temperature sensor setting
It is the function to select the temperature sensor that will decide the
indoor temperature.
Ceiling height setting
It is the function to control the wind amount stage according to the
ceiling height for the ceiling type products.
Static pressure setting
The fixed pressure setting can be set only in the duct products.
It cannot be set in other products.
RMC master/slave setting It is the function to set group control or 2-remote controller control.
Override master/slave setting
The operation master / slave selection function is to avoid other mode
operations, and it is the function to prevent the selection of the oppo-
site mode of the indoor unit set as master by the indoor units set as
slaves.
Dry contact mode setting
Dry contact function is the function that can be used only when the
dry contact devices is separately purchased and installed.
Fixed air volume
It is the function to apply different fan speeds automatically for each
thermal control status.
Zone Type Setting
It is possible to setup zone new type or old one of the product which
is available to install the damper controller.
Zone Number Setting
Zone Number is to set the number of installed zones. It's possible to
control only in zone new type.
Emergency Heater setting
It is the function to set whether to use emergency heater control func-
tion and the usage environment.
Func. control during grp.
Control setting
It is the function to set common functions or some functions to be
controlled by the master indoor unit standard during the group control.
Option Kit – Plasma / Heater /
Humidification / Elevation grill
/ Ventilation / Refrigerant leak-
age detection sensor
It is the function to set whether to mount option unit (Plasma / Humid-
ification / Heater / Ventilation / Elevation grill / Aux Heater / Refrigerant
leakage detection sensor) when it is additionally installed or removed
after the mass production.
Expand of Temperature Range This function is used for select setting temperature range option.
Indoor unit address verifica-
tion
This function allows you to check the address of the indoor unit desig-
nated by the outdoor unit.
Static pressure step setting
This is the function that static pressure of the product is divided in 11
steps for setting.
Menu Description
Guard timer
It is a function that sets the minimum running time of outdoor unit
cycle mode when switching from cooling mode to heating mode and
vice versa during Auto Operation mode.
Fan speed in Cooling thermal
off
It is a function that sets the indoor unit fan movement, in cooling
mode, when thermal is off.
Primary heater setting
It is the function to set the heater usage to have higher priority over
the outdoor unit cycle during the indoor unit heating operation.
Air conditioner Fan operation
interlocked with ventilation
setting
It is the function to set whether to operate the air conditioner fan dur-
ing the interface operation of the air conditioner and the ventilation
product.
Indoor unit Auto-Start
setting
It is a function that sets whether to restore the indoor unit operation
by resuming the previous power-on state or as power-off state in the
power failure compensation.
Occupancy duration time
setting
It is the function to set the occupied decision maintaining time among
the occupied sensor values.
CN_CC setting
It is the function to set whether to install (use) Dry Contact.
(It is not a function for Dry Contact installation, but it is a function to
set the usage of the indoor unit’s CN_CC port.)
CN_EXT setting
It is the function to set the indoor unit’s Dry Contact Port to control ex-
ternal input and output according to DI/DO set by the customer. (It is
the function to decide the usage of the contact point port (CN_EXT)
mounted in the indoor unit PCB.)
ODU function master setting It is the function to set the outdoor unit’s function Master / Slave.
Fan continuous operation
setting
It is the function to set the indoor unit’s continued Fan function usage.
It is the function to maximize the cooling/heating efficiency by the out-
door unit operating the indoor unit fan operation longer than the previ-
ous operation method.
Low noise mode priority
setting
It is the function to set the main agent of the low noise mode control.
(It is the function to set only one of the outdoor unit / remote con-
troller can control the low noise operation.)
Human detection sensor set-
ting
It is the function to set whether to install human detection sensor and
operation standard value.
Humidity sensing position It is the function to set the location to detect humidity.
ODU cycle priority This function can select standby mode or priority cooling.
Outdoor temp. for heating
stages
This function can select outdoor temperature values for use reference
point of heater and heating mode operation.
Estimated energy display This function can set to display energy data which ODU estimated.
CN_PTC setting This is a function to set PTC Port of indoor unit.
Password initialization
It is the function to initialize (0000) the password when you forgot the
password set in the remote controller.
Auto ESP
This function automatically sets the rotation speed of the fans
corresponding to each step of rated airflow for easy installation.
Dust step color setting This function is to set the dust step color.