LG 50PC1DR - - 50" Plasma TV Training Manual Download

Page: 105 / 138

Plasma Training

105

CableCARD

CABLECARD S-CARD

HOST DIAGNOSTICS

• To check the state of various TV functions related to the CableCARD, uses Host Diagnostic menu.

- press Menu->CABLE->”0"->”0"->”0" to get into Host Diagnostics menu.
- Cable Channel List’s status
- FAT, FDC status
- H/W & F/W version

CableCARD Firmware Upgrade From the Headend to the Cablecard.

• When the CableCARD Firmware Upgrade is needed, HeadEnd activates CableCARD Firmware Upgrade

operation.

* Delayed Upgrade mode (only at the stand-by state)
* Immediate Upgrade mode (stand-by or power-on state)

• CableCARD Firmware Upgrade shouldn’t be interrupted by other operations.

* During this operation, a CableCARD Firmware Upgrade reporting message is being displayed

and all remote control keys will be disabled temporarily.

* Only SA uses CableCARD Firmware Upgrade protocol and SA uses in-band tuner for this

operation.

* Motorola uses their unique technique for the CableCARD firmware Upgrade and uses OOB

tuner for this operation.

ERROR REPORTING

• Per the standard (SCTE28 Appendix E), in the case of pre-defined errors, the DCR should display an

error message showing the 161-xx
technical problem and/or set
CableCARD reset to recover from this
error.

* Failure mechanism is not the DCR

but the CableCARD.

* “xx” digits are the index of this error.

Summary of Contents for 50PC1DR - - 50" Plasma TV










































































































































Search results

Summary of Contents for 50PC1DR - - 50" Plasma TV

Reviews:

Related manuals for 50PC1DR - - 50" Plasma TV

Brands by name

Popular brands

LG 50PC1DR - - 50" Plasma TV, Training Manual

Search results

Summary of Contents for 50PC1DR - - 50" Plasma TV

Reviews:

Related manuals for 50PC1DR - - 50" Plasma TV

Brands by name

Popular brands