LG 50PC1DR - - 50" Plasma TV Training Manual Download Page 135

Page: 135 / 138

Plasma Training

135

DVR

DVR

HDD RELATED ERRORS CONTINUED (PROGRAM ERRORS)

Note

Message - From RecordedTv List

Fatal DVR error a HDD data is deleted

Delete a program which has been played because of HDD problem.

Fatal DVR error all HDD data is deleted

Delete all recorded programs becasue of DVR problem.

HDD error recovery program has started

HDD playback halts due to HDD problem. HDD Recovery begins.

HDD problem. Clip edit is not saved

HDD playback stops, cannot save clip editing because of HDD

problem.

HDD problem. Bad sector or bad connection or

other

HDD playback stops because of HDD problem.

Cannot find A/V file

Cannot play recorded program due to file error.

copy protected Video.

Cannot play Recorded Program due to copy protection.

HDD bad sector.

Cannot play Recorded Program due to bad sector.

Cannot find A/V file. Select “YES” to delete the

program

Cannot play recorded program due to file error. Do you want to

delete?

copy protected. Select “YES” to delete the

program

Cannot play Recorded Program due to copy protection. Do you

want to delete?

HDD bad sector. Select “YES” to delete the

program

Cannot play Recorded Program due to bad sector. Do you want to

delete?

Note

Message - From Gemstar Guide PlayList

Note

Message - From RecordedTv List

Fatal DVR error a HDD data is deleted

Delete a program which has been played because of HDD problem.

Fatal DVR error all HDD data is deleted

Delete all recorded programs becasue of DVR problem.

HDD error recovery program has started

HDD playback halts due to HDD problem. HDD Recovery begins.

HDD problem. Clip edit is not saved

HDD playback stops, cannot save clip editing because of HDD

problem.

HDD problem. Bad sector or bad connection or

other

HDD playback stops because of HDD problem.

Cannot find A/V file

Cannot play recorded program due to file error.

copy protected Video.

Cannot play Recorded Program due to copy protection.

HDD bad sector.

Cannot play Recorded Program due to bad sector.

Cannot find A/V file. Select “YES” to delete the

program

Cannot play recorded program due to file error. Do you want to

delete?

copy protected. Select “YES” to delete the

program

Cannot play Recorded Program due to copy protection. Do you

want to delete?

HDD bad sector. Select “YES” to delete the

program

Cannot play Recorded Program due to bad sector. Do you want to

delete?

Note

Message - From Gemstar Guide PlayList

HDD RELATED REEORS CONTINUED (TIMESHIFT ERRORS)

Current Program is copy protected

Cannot timeshift due to copy protection.

Current Program is copy protected

Stop timeshift due to copy protection.

HDD problem. Bad sector or bad connection or other

Timeshift halts due to HDD problem. HDD Recovery

begins.

Cannot Timeshift audio only channel

Timeshift cannot continue. Audio only program.

Cannot Timeshift audio only channel

Timeshift cannot start. Audio only program.

HDD problem. Bad sector or bad connection or other

Timeshift stops because of HDD problem.

Note

Message

Current Program is copy protected

Cannot timeshift due to copy protection.

Current Program is copy protected

Stop timeshift due to copy protection.

HDD problem. Bad sector or bad connection or other

Timeshift halts due to HDD problem. HDD Recovery

begins.

Cannot Timeshift audio only channel

Timeshift cannot continue. Audio only program.

Cannot Timeshift audio only channel

Timeshift cannot start. Audio only program.

HDD problem. Bad sector or bad connection or other

Timeshift stops because of HDD problem.

Note

Message

Summary of Contents for 50PC1DR - - 50" Plasma TV










































































































































Search results

Summary of Contents for 50PC1DR - - 50" Plasma TV

Reviews:

Related manuals for 50PC1DR - - 50" Plasma TV

Brands by name

Popular brands

LG 50PC1DR - - 50" Plasma TV, Training Manual

Search results

Summary of Contents for 50PC1DR - - 50" Plasma TV

Reviews:

Related manuals for 50PC1DR - - 50" Plasma TV

Brands by name

Popular brands