LG 50PC1DR - - 50" Plasma TV Training Manual Download Page 86

Page: 86 / 138

SOFTWARE UPDATES

Plasma Training

Software Updates

USING LGIDS AND GPROBE

1. On your desktop right click on My Computer or

access My Computer from the start menu.

2. Left click on Properties.

3. Left click on the Hardware tab.

4. Left click on (Device Manager...) Check the

Availability of Serial Port under “Ports” as
Communications Port (COM1) as shown in the
figure.

1. After downloading the program from GCSC. Install
\42PM1M-42PM3MV\GProbe5.1.0.18.exe

2. Run the EXE file and the install process will begin and an icon
will be placed on your desktop.

3. GProbe5 can be use by double clicking on the icon as shown in
the figure.

Opening GProbe will appear as below:

Summary of Contents for 50PC1DR - - 50" Plasma TV










































































































































Search results

Summary of Contents for 50PC1DR - - 50" Plasma TV

Reviews:

Related manuals for 50PC1DR - - 50" Plasma TV

Brands by name

Popular brands

LG 50PC1DR - - 50" Plasma TV, Training Manual

Search results

Summary of Contents for 50PC1DR - - 50" Plasma TV

Reviews:

Related manuals for 50PC1DR - - 50" Plasma TV

Brands by name

Popular brands