LG 50PC1DR - - 50" Plasma TV Training Manual Download Page 22 | Manualshive

Page: 22 / 138

background image

Plasma Training

22

Operation

OPERATION

MANUAL SOUND CONTROL

Balance

– The balance control is used to adjust the level of the left and right TV speakers. In

normal conditions, the balance control should be set to the middle (even) position. If the main
viewing position is not centered with the TV, adjust to balance control so that the speaker farther
from the main viewing position is has a higher level.

Treble

– The treble control adjusts the level of higher frequencies of the audio

spectrum.

Bass

– The bass control adjusts the level of lower frequencies of the audio spectrum.

1. Press

MENU

on the Remote Control or Front Controls

2. Use the

/

buttons to highlight the

AUDIO

Menu (3

rd

Menu) and press

3. Use the

/

buttons to highlight the desired control and press

4. Use the

/

buttons to adjust the control

5. Press

ENTER

to save the selection

6. Use the

/

buttons to change to another control or

7. Press

EXIT

to completely exit the On-Screen Menu or

MENU

to return to the previous

menu.

FRONT SURROUND

The Front Surround option provides extra processing to mimic surround sound effects using only
the TV’s 2-channel speakers.

3D EchoSound System

– SRS Labs process for improving an incoming mono audio signal to

produce a simulated stereo effect. The 3D EchoSound system will also create a three-dimensional
sound by creating a wider and deeper sound stage.

SRS TruSurround XT

– SRS Labs process for mimicking multi-channel surround sound effect from

2-channels of audio output. The SRS TruSurround XT process can also provide more clarity and bass
enrichment to stereo signals.

1. Press

MENU

on the Remote Control or Front Controls

2. Use the

/

buttons to highlight the

AUDIO

Menu (3

rd

Menu) and press

3. Use the

/

buttons to highlight

Front Surround

(7

th

Item) and press

4. Use the

/

buttons to select the desired setting

5. Press

ENTER

to save the selection

6. Press

EXIT

to completely exit the On-Screen Menu or

MENU

to return to the previous

menu.

TV SPEAKER

The TV Speaker selection option is used to either enable or disable the TV’s internal speakers. If the
TV is connected to a home theater system and there is no desire for audio from the TV’s speakers,
the TV’s speakers may be turned off.

1. Press

MENU

on the Remote Control or Front Controls

2. Use the

/

buttons to highlight the

AUDIO

Menu (3

rd

Menu) and press 4

3. Use the

/

buttons to highlight

TV Speakers

(8

th

Item) and press

4. Use the

/

buttons to select the desired setting

5. Press

ENTER

to save the selection

«
...
20
21
22
23
24
...
»

Summary of Contents for 50PC1DR - - 50" Plasma TV











































































































































Reviews:

No comments

Related manuals for 50PC1DR - - 50" Plasma TV

Brand: Sceptre Pages: 56

VX240M - 24" LCD TV

Brand: Vizio Pages: 53

Brand: Sharp Pages: 44

AQUOS 4T-B60CJ1U

Brand: Sharp Pages: 46

Brand: Vizio Pages: 35

Brand: Vizio Pages: 44

SV420XVT1A - 42" LCD TV

Brand: Vizio Pages: 104

Brand: Vizio Pages: 2

Brand: Tecslate Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands