LG 50PC1DR - - 50" Plasma TV Training Manual Download Page 94

Page: 94 / 138

SOFTWARE UPDATES

Plasma Training

Software Updates

•When the TV is in the ON state these additional LED’s will be lit.

Control PCB

Connector to JIG (P101)

This LED will be blinking

Press and hold the (AUTO) button for 3 seconds and release the (AUTO) button.

Within a few seconds the display will indicate (ERASING) and the LED will be
flashing green.

The display will next display (WRITING) and the LED will be blinking.

The display will then display (VERIFYING) and the LED will be blinking.

If the update was successful the display will indicate (OK) and the LED
will be on.

What will be seen during the update.

Summary of Contents for 50PC1DR - - 50" Plasma TV










































































































































Search results

Summary of Contents for 50PC1DR - - 50" Plasma TV

Reviews:

Related manuals for 50PC1DR - - 50" Plasma TV

Brands by name

Popular brands

LG 50PC1DR - - 50" Plasma TV, Training Manual

Search results

Summary of Contents for 50PC1DR - - 50" Plasma TV

Reviews:

Related manuals for 50PC1DR - - 50" Plasma TV

Brands by name

Popular brands