manualshive.com logo in svg

Lexmark 6500E, User Manual

Share
Download
Lexmark 6500E User Manual Download Page 275

52 Not enough free space in flash memory for resources

Try one or more of the following:

•

Touch 

Continue

 to clear the message and continue printing.

Downloaded fonts and macros not previously stored in flash memory are deleted.

•

Delete fonts, macros, and other data stored in flash memory.

•

Upgrade to a larger capacity flash memory card.

54 Network [x] software error

Try one or more of the following:

•

Touch 

Continue

 to continue printing.

•

Turn the printer off, wait for about 10 seconds, and then turn the printer back on.

•

Upgrade (flash) the network firmware in the printer.

54 Serial option [x] error

Try one or more of the following:

•

Make sure the serial cable is connected properly and is the correct one for the serial port.

•

Make sure the serial interface parameters (protocol, baud, parity, and data bits) are set correctly on the scanner
and host computer.

•

Touch 

Continue

 to clear the message.

•

Turn the scanner power off and then back on to reset the scanner.

54 Standard network software error

Try one or more of the following:

•

Touch 

Continue

 to continue printing.

•

Turn the printer off and then back on to reset the printer.

•

Upgrade (flash) the network firmware in the printer or print server.

55 Unsupported option in slot [x]

1

Turn the scanner off.

2

Unplug the power cord from the wall outlet.

3

Remove the unsupported option card from the scanner system board, and then replace it with a supported card.

4

Connect the power cord to a properly grounded electrical outlet.

5

Turn the scanner back on.

Troubleshooting

275

Summary of Contents for 6500E


















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands