LevelOne IES-2881 User Manual Download Page 94

Page: 94 / 162

User Manual

Page 94

Use

install image

command to upgrade firmware from tftp server to switch.

Command Syntax:

install image IP-ADDRESS WORD
IP-ADDRESS specifies the IP address of tftp server.

WORD specifies the file name to be upgraded to switch.

Example:

The following example specifies upgrading firmware (file name:

flash.tgz

) from tftp server

(IP address:

192.168.1.100)

to switch:

switch_a#install image 192.168.1.100 flash.tgz
switch_a#

Please follow the message on the screen during the firmware upgrade process. Do not
turn off the power or perform other functions during this period of time.

eboot the switch

after completing the upgrade process.

Summary of Contents for IES-2881



































































































































































Search results

Summary of Contents for IES-2881

Reviews:

Related manuals for IES-2881

Brands by name

Popular brands

LevelOne IES-2881, User Manual

Search results

Summary of Contents for IES-2881

Reviews:

Related manuals for IES-2881

Brands by name

Popular brands