LevelOne IES-2881 User Manual Download Page 28

Page: 28 / 162

User Manual

Page 28

Understanding the Browser Interface

The web browser interface provides groups of point-and-click buttons at the left field of
the screen for configuring and managing the switch.

SYSTEM

System Information, System Name/Password, IP Address, Save Configuration, Firmware
Upgrade, Reboot, Logout

PORT

Configuration, Port Status, Rate Control, RMON Statistics, Per Port Vlan Activities

SWITCHING

Bridging, Static MAC Entry, Port Mirroring

TRUNKING

Port Trunking

STP / RING

Global Configuration, RSTP Port Setting, MSTP Properties, MSTP Instance Setting, MSTP
Port Setting, Ring Setting

VLAN

VLAN Mode Setting, 802.1Q VLAN Setting, 802.1Q Port Setting, Port Based VLAN

Summary of Contents for IES-2881



































































































































































Search results

Summary of Contents for IES-2881

Reviews:

Related manuals for IES-2881

Brands by name

Popular brands

LevelOne IES-2881, User Manual

Search results

Summary of Contents for IES-2881

Reviews:

Related manuals for IES-2881

Brands by name

Popular brands