LevelOne IES-2881 User Manual Download Page 129

Page: 129 / 162

User Manual

Page 129

SNMP

SNMP General Setting, SNMP v1/v2c, SNMP v3

SNMP General Setting

SNMP Status:
1.

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Use

snmp-server enable

command to enable and

no snmp-server enable

command to

disable SNMP to the switch.

3.

Command Syntax:

(no) snmp-server enable

4.

Example:

The following example enables SNMP to the switch:

switch_a(config)#snmp-server enable
switch_a(config)#

Description:
1.

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Use

snmp-server description

command to specify and

no snmp-server description

command to remove description for SNMP.

3.

Command Syntax:

snmp-server description DESCRIPTION
no snmp-server description

DESCRIPTION The description for SNMP.

Example:

The following example specifies description (

description

) for SNMP:

switch_a(config)#snmp-server description description
switch_a(config)#

Summary of Contents for IES-2881



































































































































































Search results

Summary of Contents for IES-2881

Reviews:

Related manuals for IES-2881

Brands by name

Popular brands

LevelOne IES-2881, User Manual

Search results

Summary of Contents for IES-2881

Reviews:

Related manuals for IES-2881

Brands by name

Popular brands