Lenovo 10HA Hardware Maintenance Manual Download

Page: 110 / 142

6. Remove the screw that secures the converter board to the bracket. Then, lift the converter board

upward to remove it from the bracket.

Figure 44. Removing the converter board

7. Align the two holes in the new converter board with the corresponding hooks on the bracket. Then,

install the new converter board as shown and install the screw to secure the converter board.

Figure 45. Installing the converter board

8. Connect the two converter-board cables to the new converter board.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 112.

Replacing the converter board bracket

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter

1 “Read this first: Important safety information” on page 1.

To replace the converter board bracket, do the following:

1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect

all power cords from electrical outlets and disconnect all cables that are connected to the computer.

2. Place a soft, clean towel or cloth on the desk or surface. Hold the sides of your computer and gently lay

it down so that the screen is against the surface and the cover is facing up.

104

Lenovo S200z Hardware Maintenance Manual

Summary of Contents for 10HA















































































































































Search results

Summary of Contents for 10HA

Reviews:

Related manuals for 10HA

Brands by name

Popular brands

Lenovo 10HA, Hardware Maintenance Manual

Search results

Summary of Contents for 10HA

Reviews:

Related manuals for 10HA

Brands by name

Popular brands