Leader Electronics Corp. LT 443D Instruction Manual Download Page 121

Page: 121 / 239

BL-4

4.2

Selecting Output Connector

This mode is used to select one of three black signal output systems to set the format and

timing.

Select [BLACK 1, 2], [BLACK 3, 4], or [BLACK 5, 6] by pressing the Up or Down key, then

press the [ENTER] key. In case of [BLACK 1, 2 SIGNAL] is selected:

2. BLACK 1, 2 SIGNAL

▼

FORMAT

Hierarchy level 2

▼

FORMAT

▲

TIMING

4.3

FORMAT SELECT

This mode is used to select the output signal format.

4.3.1 Setting FORMAT

(1) Select [FORMAT SELECT] from the [2. BLACK SETTING] menu, then press the [EN-

TER] key.

(2) The format marked with asterisk is currently selected.

Select the desired format by pressing the Up or Down key, then press the [ENTER] key.

3. FORMAT BLACK 1, 2

＊

1080i/59.94

＊

Refer to “LIST OF BLACK SIGNAL

FORMAT” for detail.

In case of [1080i/59.94] is

selected.

Hierarchy level 3

1035i/60

1035i/59.94

1080i/60

1080i/59.94

1080i/50

1080p/30

1080p/29.97

1080p/25

1080p/24

1080p/23.98

1080PsF/24

1080PsF/23.98

720p/60

720p/59.94

720p/50

720p/30

720p/29.97

720p/25

720p/24

720p/23.98

NTSC BB

NTSC BB+REF

NTSC BB+ID

NTSC BB+REF+ID

NTSC BB+SETUP

NTSC BB+S+REF

NTSC BB+S+ID

NTSC BB+S+R+ID

525i/59.94

525p/59.94

PAL BB

PAL BB+REF

625i/50

625p/50

＊

Summary of Contents for LT 443D
















































































































































































































































Search results

Summary of Contents for LT 443D

Reviews:

Related manuals for LT 443D

Brands by name

Popular brands

Leader Electronics Corp. LT 443D, Instruction Manual

Search results

Summary of Contents for LT 443D

Reviews:

Related manuals for LT 443D

Brands by name

Popular brands