Leader Electronics Corp. LT 443D Instruction Manual Download Page 32

Page: 32 / 239

4-9

4.5.6 ETHERNET SET

The ethernet capability can remotely control and monitor genlock status.

The current setting value is displayed.

The underline cursor can be moved by pressing the [Left] or [Right] key.

The cursored number can be changed by pressing the [Up] or [Down] key.

Pressing the [ENTER] key enters data.

2. ETHERNET SET

IP: 192. 168. 20. 63

■

□

CANCEL

Hierarchy level 2

＊

”ETHER” is set to IP address when power is turned on.

4.5.6.1 Remote Control via ETHER Port

This section describes the remote control procedure using the “TELNET” software.

Select “Run” from the Start menu.

To run application software, enter “TELNET” in the

“Open” column, then click “OK.”

Click “Remote System” in the “Connect” menu.

Summary of Contents for LT 443D
















































































































































































































































Search results

Summary of Contents for LT 443D

Reviews:

Leader Electronics Corp. LT 443D, Instruction Manual, Page: 32 / 239

Search results

Summary of Contents for LT 443D

Reviews: