Leader Electronics Corp. LT 443D Instruction Manual Download Page 13

Page: 13 / 239

2-2

2.3

Specifications

2.3.1 Compartment

Number of compartments

ID Function

Automatically identifies the unit installed.

＊

2 Refer to Section 2.5 and specifications of each unit.

2.3.2 LCD Panel

Number of Characters

20 characters x 2 lines can be displayed (w/backlight).

2.3.3 Internal Clock

Internal Reference Frequency

27 MHz

2.3.4 Memory Card Slot

Function

Storing/reading preset data

Reading logo mark data

Reading NATURAL PICTURE data

＊

Applicable Card

Compact flash memory card (CFA TYPE-1)

＊

3 The NATURAL picture function is only usable when the LT 443D-70 Option is installed

in the mainframe.

＊

4 No compact flash memory card is supplied as standard accessory.

Memory cards produced by following manufacturers should be procured (as of August
2002):SanDisk

＊

5 A microdrive can’t be used.

2.3.5 External Interface

Ethernet

10/100 Base T (Automatic selection)

Function

Transferring operation status (e.g., genlock status)

Remote control (e.g., pattern switching)

USB (Universal Serial Bus)

Applicable to USB 1.1

Function

This function will be supported. (Hardware is installed as

standard.)

2.3.6 General Specifications

Environmental Conditions

Operating Temperature Range

0 to 40 ˚C

Operating Humidity Range

≤

90% RH (without condensation)

Spec-Guaranteed Temperature Range

10 to 35 ˚C

Spec-Guaranteed Humidity Range

≤

85% RH (without condensation)

Operating Environment

Indoor use

Operating Altitude

Up to 2000 m

Overvoltage Category

Pollution Degree

Power Requirements

90 to 250 VAC, 50/60 Hz

Power Consumption

Approx. 150 W max. (Approx. 75 W max.

＊

Dimensions and Weight

426 (W) x 44 (H) x 560 (D) mm,

Approx. 7 kg

＊

Summary of Contents for LT 443D
















































































































































































































































Search results

Summary of Contents for LT 443D

Reviews:

Related manuals for LT 443D

Brands by name

Popular brands

Leader Electronics Corp. LT 443D, Instruction Manual

Search results

Summary of Contents for LT 443D

Reviews:

Related manuals for LT 443D

Brands by name

Popular brands