Leader Electronics Corp. LT 443D Instruction Manual Download Page 145

Page: 145 / 239

SD/SDB-19

2. NATURAL PICTURE

▼

SELECT PICTURE 1

▼

SELECT PICTURE 1

SELECT PICTURE 2

SELECT PICTURE 3

SELECT PICTURE 4

SELECT PICTURE 5

FILE TRANSFER

▲

SET TO CF CARD

(1) CF Card with NATURAL PICTURE

(2) CF Card without NATURAL PICTURE

2. NATURAL PICTURE

NO DATA!

Warning message is displayed; no NATURAL PICTURE file cannot be selected.

If the CF card is inserted, return to the top menu of [NATURAL PICTURE], then apply

the procedure above again to read NATURAL PICTURE file.

4.9.1 Selecting SELECT PICTURE File

(1) Select [SELECT PICTURE 1] from the [2. NATURAL PICTURE] menu by pressing the

Up or Down key, then press the [ENTER] key.

The NATURAL PICTURE file list

＊

(stored on the CF card in the MEMORY CARD slot)

corresponding to the current format size is displayed.

＊

“E:\IMAGE\H525” folder for 525 line format

(E:\ indicates CF card drive.)

“E:\IMAGE\H625” folder for 625 line format

3. SELECT PICTURE 1

▼＊

FLOWER 1 1/10

Hierarchy level 3

Hierarchy level 2

FLOWER 2

2/10

FLOWER 3

3/10

GREEN 4/10

•

YOKOHAMA

7/10

JAPAN

8/10

PHOTO 1

9/10

PHOTO 2 10/10

▼＊

FLOWER 1 1/10

Summary of Contents for LT 443D
















































































































































































































































Search results

Summary of Contents for LT 443D

Reviews:

Leader Electronics Corp. LT 443D, Instruction Manual, Page: 145 / 239

Search results

Summary of Contents for LT 443D

Reviews: