Leader Electronics Corp. LT 443D Instruction Manual Download Page 143

Page: 143 / 239

SD/SDB-17

(3) Setting SCROLL SPEED

This mode is used to set the scroll speed.

Select [SPEED] by pressing the Up or Down key, then press the [ENTER] key.

4. SCROLL SPEED

■

H: 0 DOT

□

V: 0 DOT

Hierarchy level 4

Position the [

■

] to [H] or [V] by pressing the Left or Right key, then set the scroll speed

by pressing the Up or Down key.

The settable range is 0 to 256 dots in four dot steps in the horizontal direction, 0 to 256

dots in two dot steps in the vertical direction.

Pressing the [ENTER] key enters data. The menu returns to hierarchy level 3 [3.

SCROLL PARAM. SET].

Pressing the [MENU] key selects the next higher hierarchy.

4.7.2 Setting SCROLL ON/OFF

This mode is used to set the pattern scroll mode on or off.

(1) Select [SCROLL ON/OFF] from the [2. PATTERN SCROLL] menu by pressing the Up

or Down key, then press the [ENTER] key.

3. SCROLL ON/OFF

□

ON:

■

OFF

Hierarchy level 3

(2) Position the [

■

] to [ON] or [OFF] by pressing the Left or Right key, then press the

[ENTER] key. The menu returns to hierarchy level 2 [2. PATTERN SCROLL].

Pressing the [MENU] key selects the next higher hierarchy.

4.8.

PATTERN CHANGE

All patterns (except CHECK FIELD pattern) indicated on the front panel are sequentially

selected from the left to right and displayed.

Select [ PATTERN CHANGE] from the [1. SD SETTING] menu, then press the [ENTER]

key.

1. SD SETTING

PATTERN CHANGE

Hierarchy level 1

2. PATTERN CHANGE

▼

SPEED

Hierarchy level 2

▼

SPEED

▲

CHANGE ON/OFF

Summary of Contents for LT 443D
















































































































































































































































Search results

Summary of Contents for LT 443D

Reviews:

Leader Electronics Corp. LT 443D, Instruction Manual, Page: 143 / 239

Search results

Summary of Contents for LT 443D

Reviews: