Leader Electronics Corp. LT 443D Instruction Manual Download Page 181

Page: 181 / 239

DA-7

▼

CH 1/CH 2 SETTING

CH 3/CH 4 SETTING

CH 5/CH 6 SETTING

CH 7/CH 8 SETTING

WCLK LEVEL

TIMING

▲

EXIT

3.3.2.2 Setting 2-Channel Output

Select the desired item (i.e., output ON/OFF, resolution, preemphasis) from the menu

selected in the Section 3.3.2.1, “Selecting Channel” by pressing the [Up] or [Down]

key, then press the [ENTER] key.

3.3.2 Setting AES/EBU Digital Audio Signal

3.3.2.1 Selecting Channel To be Set

Select the desired 2-channel output from the [1. DA SETTING] menu by pressing the

[Up] or [Down] key, then press the [ENTER] key.

Example: To set the CH 1/CH 2 output, select [CH 1/CH 2 SETTING].

UNIT compartment No.

Select channel from this group.

1. DA SETTING #1

▼

CH 1/CH 2 SETTING

2. CH 1/CH 2 SETTING

▼

AUDIO ON/OFF

▼

AUDIO ON/OFF

RESOLUTION

EMPHASIS

▲

CH SETTING

＊

The following steps describe setting procedure in case of the CH 1/CH 2 is selected.

(1) AUDIO ON/OFF

Select [ON] or [OFF] by pressing the [Left] or [Right] key, then press the [ENTER] key.

[

■

] indicates the selected item.

＊

When [ON] or [OFF] is selected by pressing the [Left] or [Right] key, this item is

executed. To store data, press the [ENTER] key. If exiting the menu without

pressing the [ENTER] key, no data is stored.

Select item from this group.

3. AUDIO ON/OFF

■

□

OFF

Hierarchy level 1

Hierarchy level 2

Hierarchy level 3

Summary of Contents for LT 443D
















































































































































































































































Search results

Summary of Contents for LT 443D

Reviews:

Leader Electronics Corp. LT 443D, Instruction Manual, Page: 181 / 239

Search results

Summary of Contents for LT 443D

Reviews: