manualshive.com logo in svg

Lake Shore 350, User Manual

Share
Download
Lake Shore 350 User Manual Download Page 97

  

4.5.2   Analog Outputs       

83

 

                                                        

   

|

   

www.lakeshore.com

To set Heater Range, first configure the front panel display to show the desired control 
loop information, then use the 

Heater Range

 key on the front panel. A quick way to 

access the setting if the control loop information is not already being displayed is to 
press 

A

, 

B

, 

C

, or 

D

 on the front panel to temporarily display the control loop informa-

tion while the new setting is entered. Refer to section 4.2 for details on configuring 
the front panel display. 

Menu Navigation: 

Heater Range

Q

(Off, On, Range 1, Range 2, Range 3, Range 4, Range 5) 

Default: Off
Interface Command: 

RANGE

4.5.1.5.9   ALL OFF

The 

ALL OFF

 key is provided as a means of shutting down all control outputs with one 

key. It is equivalent to setting the Heater Range parameter of all outputs to Off. 

This function is always active even if the keypad is locked or when it is in remote mode.

4.5.2 Analog Outputs

The analog outputs, 3 and 4, are variable DC voltage sources that have a range from 

–10 V to +10 V. The voltage is generated by a 16-bit D/A converter with resolution of 
0.3 mV or 0.003% of full scale. This output can be configured to a Closed Loop PID, 
Zone, Open Loop, Warm Up Supply, or Monitor Out mode. The Closed Loop PID mode 
can be used to control temperature. It can also be set up for bipolar PID control, which 
is useful when controlling a thermoelectric device. Refer to section 5.4 for more infor-
mation on setting up thermoelectric devices. The Open Loop mode can be used to set 
the output to a specific, constant value. Refer to section 4.5.1.4.3 for details on Open 
Loop Mode. The Warm Up Supply mode uses the output to drive the programming 
input for an external power supply for the purpose of rapidly warming a system to a 
user-specified temperature. The Monitor Out mode uses the output to provide a volt-
age proportional to an input sensor reading to be used by an external device such as a 
data logger.

The voltage output is designed to provide up to 1 W into a 100 

)

 heater. The output is cur-

rent limited to slightly over 100 mA, and therefore, a heater value less than 100 

)

 can 

drive the output into current limit. This condition will not damage the output, but it can 
result in discontinuous temperature control.

4.5.2.1   Warm Up Supply

Warm Up Supply mode is designed for controlling an external power supply used for 
rapidly increasing the temperature in the controlled system, for example, to bring a 
system to room temperature in order to change samples. Refer to section 5.5 for more 
information on warm up supply operation. Refer to section 3.6.5 for the procedure to 
install an external power supply for warm up supply mode.

4.5.2.2   Monitor Out

Refer to section 5.6 for more information on Monitor Out mode. 

4.6  Interface

The Model 350 has three computer interfaces: IEEE-488, USB, and Ethernet. Only one 
of these interfaces can be active at one time. Use the Interface menu to configure 
which interface is active, and to configure the parameters related to the selected 
interface.

Menu Navigation: 

Interface

Q

 

Enabled

Q

 (USB, Ethernet, IEEE-488)

Default: USB

Summary of Contents for 350

































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands