manualshive.com logo in svg

Labcyte Echo 520, User Manual, Page: 84 / 200

Share
Download
Labcyte Echo 520 User Manual Download Page 84

4-2

Echo Liquid Handler User Manual

4.1

Startup/Shutdown

At this point, the hardware and client PC software installations should be 
complete. All fluid, air, and electrical connections should be complete and 
functioning. Your Labcyte field engineer performs a set of function tests to 
ensure that the system is operating correctly. 

4.1.1 Turn on Echo power

Turn on the Echo liquid handler by pressing the AC power 
switch located on the back panel. 

The following message may appear while the Echo liquid 
handler initializes:

Figure 4.1  Connection failure message

Possible causes for connection failure include:

The Echo liquid handler has not completed its initialization.

Check the gripper stage homing sequences, particularly the theta 
rotation of the destination gripper stage. 

Check the door opening sequence.

The Ethernet cable is not connected between the client PC and the 
Echo liquid handler.

The Echo software is not configured to connect to the instrument (IP 
address or hostname is missing or incorrect).

Check for the cause, attempt to resolve the problem, and try to launch the 
software again. If the message persists, call Labcyte Service and Support.

Summary of Contents for Echo 520









































































































































































































Reviews:

No comments