manualshive.com logo in svg

Labcyte Echo 520, User Manual, Page: 155 / 200

Share
Download
Labcyte Echo 520 User Manual Download Page 155

Echo Liquid Handler Software

5-55

Save Transfer data to disk: 

Normally, the 

data collected during a source plate transfer is 
deleted when the transfer is complete. If the 

S

AVE

 T

RANSFER

 D

ATA

 

TO

 D

ISK

 checkbox is 

selected, the transfer data will be stored on the client PC disk. There is no 
reason to save transfer data during normal operation. The data file is stored 
to <InstallDir>\Labcyte\Medman\Data. Transfer data can be useful to 
Labcyte personnel during diagnostic troubleshooting.

Default: liquid transfer data is not saved to the Echo controller.

Ignore Source Plate Sensor Check: 

Selecting 

the 

I

GNORE

 S

OURCE

 P

LATE

 S

ENSOR

 C

HECK

 

checkbox bypasses the source plate present 
sensor. This may be useful when an individual source plate does not fit 
correctly. A run protocol procedure can execute without triggering a “no 
source plate loaded” error message.

Default: The source plate presence detect sensor is not ignored.

Ignore Destination Plate Sensor Check: 

Selecting the 

I

GNORE

 D

ESTINATION

 P

LATE

 S

ENSOR

 

C

HECK

 checkbox bypasses the destination plate 

present sensor. This may be useful when an 
individual destination plate does not fit correctly, or droplets are being 
transferred to a microplate lid or other substrate that does not fit like a 
microplate. A run protocol procedure can execute without triggering a “no 
destination plate loaded” error message.

Default: The destination plate presence detect sensor is not ignored.

5.5.2 Advanced solvent concentration (DMSO 

only)

If the DMSO concentration in a source plate is known, accuracy can be 
improved by specifying it prior to performing liquid transfers. 

Note:  

The Solvent Concentration function assumes the solvent is 

DMSO, therefore this function is not relevant for aqueous solutions. 

The DMSO concentration information entered will be used with each 
source microplate until one of the following occurs:

The 

U

SE

 

PREDEFINED

 checkbox is cleared, or

New DMSO concentration information is entered, or

The Echo software is restarted.

Summary of Contents for Echo 520









































































































































































































Reviews:

No comments