manualshive.com logo in svg

Labcyte Echo 520, User Manual, Page: 154 / 200

Share
Download
Labcyte Echo 520 User Manual Download Page 154

5-54

Echo Liquid Handler User Manual

If the source plate fluid is stable, the survey interval can be safely increased. 
For example, “every 5 plates” will cause a new survey to be performed 
when the source plate and first destination plate are loaded, and every fifth 
destination plate thereafter. Increasing the survey interval may improve 
throughput.

Default: 1.

Note:  

The survey interval can be set to 0; however, with this setting 

the protocol will not survey the plate. 

Assume Homogeneous Plate: 

When a 

source plate is surveyed to measure the 
DMSO/water ratio in each well, the Echo 
liquid handler creates a DMSO concentration map of the entire plate. This 
map is post-processed using a moving average filter if the 

A

SSUME

 

H

OMOGENEOUS

 P

LATE

 

checkbox is selected. There is no overhead associated 

with this processing. Typically, better liquid transfers are obtained using 
post-processing when the source microplate contents are homogeneous. A 
homogeneous source microplate is one where the solution to be 
transferred is very similar, well-to-well.

If the 

U

SE

 P

REDEFINED

 checkbox is selected, the Assume Homogeneous 

Plate feature is unavailable, and its checkbox is “grayed out.”

Default: Assume homogeneous plate off.

Power Monitoring: 

Selecting the 

P

OWER

 

M

ONITORING

 checkbox causes the Echo liquid handler 

to monitor the RF power used to eject each fluid droplet. Labcyte 
recommends that power monitoring not be enabled by the user unless 
directed to do so by Labcyte personnel. Enabling power monitoring adds 
significant overhead to each droplet ejection and decreases liquid transfer 
throughput.

Default: Power monitoring off.

Save Plate-Survey Data to Disk: 

The data 

collected during a source plate survey is held in 
cache memory. It is replaced when the next 
source plate survey is performed. If the 

S

AVE

 

P

LATE

-S

URVEY

 D

ATA

 

TO

 D

ISK

 checkbox is selected, the survey data will be 

stored on the client PC disk. The data file is stored to <InstallDir>\Labcyte\
Medman\Data. This data can be useful to Labcyte personnel during 
diagnostic troubleshooting.

Default: Source plate survey data is not saved on the Echo controller.

Summary of Contents for Echo 520









































































































































































































Reviews:

No comments