Home
/
Labcyte
/
Echo 520
/
User Manual

Labcyte Echo 520, User Manual, Page: 157 / 200

Share

Page: 157 / 200

Labcyte Echo 520 User Manual Download Page 157

Echo Liquid Handler Software

5-57

Cancel:

Clicking the

C

ANCEL

button closes the Solvent Platemap dialog box

with no action taken.

5.5.3 Advanced Echo control

There are cases when the Echo controller must be shutdown or restarted.
The Echo controller is the hardware and software resident on the Echo
instrument that controls all functions of the instrument.

Figure 5.51 Echo controller restart or shutdown

Caution:

If the Echo software is connected to a stub mode Echo

liquid handler service running on the client PC, clicking the

H

ARD

R

ESET

button will “reset” the client PC, and clicking the

S

HUTDOWN

button will “shutdown” the client PC.

Soft Reset:

Clicking the

S

OFT

R

ESET

button causes the Echo service to be

restarted on the Echo controller.

Hard Reset:

Clicking the

H

ARD

R

ESET

button causes the Echo controller to

reboot. After rebooting the Echo controller, any attached client computer
programs must be reconnected to the Echo controller.

Shutdown:

Clicking the

S

HUTDOWN

button causes the Echo controller to

perform its normal “shutdown” procedure. If an Echo liquid handler needs
to be turned off, its controller should always be “shutdown” before the
Echo AC power switch is turned off.

«
...
155
156
157
158
159
...
»

Summary of Contents for Echo 520









































































































































































































Reviews:

No comments