manualshive.com logo in svg

Labcyte Echo 520, User Manual, Page: 182 / 200

Share
Download
Labcyte Echo 520 User Manual Download Page 182

7-2

Echo Liquid Handler User Manual

7.2

Setup problems

If the Echo software cannot connect with the Echo liquid handler, the 
following message will appear:

Figure 7.1  Connection failure message

This message is commonly seen and is not a cause for alarm. Possible 
causes for the connection failure include:

The Echo liquid handler has not been turned on.

The Echo liquid handler has been turned on, but it has not completed 
its initialization.

Check the gripper stage homing sequences, particularly the theta 
rotation of the destination gripper stage. 

Check the door opening sequence.

The Ethernet cable is not connected between the computer and the 
Echo liquid handler.

The Echo software is not configured (IP address or hostname) to 
connect to the instrument.

The Echo liquid handler is failing to communicate. 

Check for the cause, attempt to resolve the problem, and try to launch the 
software again. If the message persists, call Labcyte Service and Support.

Summary of Contents for Echo 520









































































































































































































Reviews:

No comments