manualshive.com logo in svg

Labcyte Echo 520, User Manual, Page: 71 / 200

Share
Download
Labcyte Echo 520 User Manual Download Page 71

System Description

3-13

The location of each scanner depends on the location of your barcode 
labels on the microplates. You can use either the front scanner or the side 
scanner, but not both at the same time.

Note:  

Several terms are used to specify barcode locations on a 

microplate. Standing in front of an Echo liquid handler, the two 
readable barcode locations are identified as follows:

Figure 3.14  Barcode label locations

Note:  

Always place side barcode labels on the 

left

 side of both source 

and destination microplates. The Echo liquid handler uses the 

left

 

barcode scanner to read the barcode on the source plate, but uses the 

right

 barcode scanner to read the barcode on the destination plate—

after it is inverted. 

Labcyte provides barcode scanners that support the following 
barcode types:

Code 93

Code 39

Code 128

Codabar

Pharmacode

Interleaved 2 of 5

UPC/EAN

Contact Labcyte Service and Support to install or move the barcode 
scanners. 

See “Contact information” on page 7-1.

See “Barcode Locations” on page B-1

 for limitations on where barcode 

labels can be placed on a microplate.

Left, short, or 
west position

Front, long, or south position

Summary of Contents for Echo 520









































































































































































































Reviews:

No comments