manualshive.com logo in svg

Labcyte Echo 520, User Manual, Page: 11 / 200

Share
Download
Labcyte Echo 520 User Manual Download Page 11

Preface

xi

Caution:  

Do not obstruct the air vents. Keep all air vents free of dirt or 

dust.

Caution:  

Handle the Echo liquid handler coupling fluid and waste water 

carefully. Avoid all spills.

Caution:  

Keep corrosive agents, or otherwise damaging material, away 

from the Echo liquid handler and its attached devices.

Caution:  

Do not expose the Echo liquid handler to excessive moisture 

(>80% relative humidity). Moisture, or condensation, can damage electrical 
components.

Caution:  

Do not expose the Echo liquid handler to temperatures outside 

of the storage range: 5°C–45°C (41°F–113°F). Temperatures outside of this 
range can damage the instrument.

Caution:  

Do not run the Echo liquid handler without the chiller. Ensure 

that the chiller is correctly connected to the Echo instrument and is running 
at the recommended temperature. Incorrect coupling fluid temperature can 
reduce the precision and accuracy of the fluid that is transferred. Extreme 
fluid temperatures can potentially damage the acoustic transducer. 

Caution:  

Do not allow the acoustic transducer to dry out. If the Echo 

liquid handler is going to be shut down for longer than a week, start up 
and run the pump once a week to keep the acoustic transducer wet. 

See 

“Extended Non-Use and Storage” on page 6-19

.

Caution:  

Do not run the pump if the chiller tubing is not connected. 

Running the pump without the chiller tubing may damage other system 
components. 

Caution:  

Do not run the pump without the vacuum source connected and 

active. Running the pump without vacuum can lead to flooding the system 
or a system error. 

Summary of Contents for Echo 520









































































































































































































Reviews:

No comments