Kyocera FS-600 User Manual Download Page 94

Page: 94 / 144

Chapter 5 Troubleshooting

5-3

Symptom

Check Items

Corrective Action

Nothing lights on the

control panel even

when power is turned

on and the fan makes

no noise.

Check that the power cord is

properly plugged into the power

outlet.

Turn off the printer's power, plug in the

power cord securely, and try turning on the

printer's power again.

Check that the power switch is really in the on position.

The printer prints a

status page, but data

from the computer is

not being printed

normally.

Check the interface cable.

Connect both ends of the interface cable

securely. Try replacing the printer cable. For

details on the parallel interface of this printer,

see

Appendix C

Check program files and application

software.

Try printing another file or using another

print command. If the problem occurs only

with a specific file or application, check the

printer settings for that application.

If you still cannot correct a printer problem even after checking the above, please contact your

Kyocera dealer.

Summary of Contents for FS-600

















































































































































Search results

Summary of Contents for FS-600

Reviews:

Related manuals for FS-600

Brands by name

Popular brands

Kyocera FS-600, User Manual

Search results

Summary of Contents for FS-600

Reviews:

Related manuals for FS-600

Brands by name

Popular brands