Kyocera FS-600 User Manual Download Page 98

Page: 98 / 144

Chapter 5 Troubleshooting

5-7

Printed Results

Corrective Action

Dirt on the top edge or back of the paper

Check the transfer roller.

Lift the process unit out of the printer and check whether the

transfer roller is dirty. If so, print several pages to eliminate

the dirt.

Check the registration roller.

Lift the process unit out of the printer and check whether the

registration roller is soiled with toner. If so, wipe it clean using

the supplied cleaning cloth.

Characters out of position.

Check the file or program.

See if the problem is caused by an error with PRESCRIBE IIe

commands. If the problem occurs only with a specific file or

program, the most likely cause is an error in a parameter to a

command or command syntax.

Summary of Contents for FS-600

















































































































































Search results

Summary of Contents for FS-600

Reviews:

Related manuals for FS-600

Brands by name

Popular brands

Kyocera FS-600, User Manual

Search results

Summary of Contents for FS-600

Reviews:

Related manuals for FS-600

Brands by name

Popular brands