Kyocera FS-600 User Manual Download Page 122

Page: 122 / 144

Parallel Interface

C-2

Parallel Interface

Parallel interface communication modes

The printer features the fast data transmission mode on the parallel interface. The parallel interface

mode can be changed by using the PRESCRIBE FRPO O0 command. See the

Programming manual

(in the Kyocera Digital Library CD-ROM) for details.

Note______________________________________________________________________

Use a parallel printer cable that complies with the IEEE1284 standards.

Nibble (high)

(FRPO O0, 5; [default])

High speed data communication is used in compliance with the IEEE 1284 standard. Ordinarily, you

should leave this setting unchanged.

Auto

(FRPO O0, 70;)

The printer automatically changes its communication mode to the one the host computer is currently

using.

Normal

(FRPO O0, 0;)

The printer uses the communication method described by the normal definitions of the Centronics

interface.

High-speed

(FRPO O0, 1;)

This mode enables faster data reception from the host computer by the normal definitions of the

Centronics interface..

Summary of Contents for FS-600

















































































































































Search results

Summary of Contents for FS-600

Reviews:

Related manuals for FS-600

Brands by name

Popular brands

Kyocera FS-600, User Manual

Search results

Summary of Contents for FS-600

Reviews:

Related manuals for FS-600

Brands by name

Popular brands