Kyocera FS-600 User Manual Download Page 99

Page: 99 / 144

Indicators

5-8

Indicators

This section explains the indicators on the control panel and the appropriate corrective action to take

in each case.

Whether the indicator is lit, flashing or off is indicated as shown in the following diagram. Although

there is fast flashing and slow flashing, they are not distinguished diagrammatically.

Lit

Flashing

Off

Maintenance Indications

Indicators

Corrective Action

The top cover is open.

Close it tightly.

(In this example, the printer’s cassette is selected.)

The paper source is out of paper.

Add paper to the paper cassette or manual feed tray.

(In this example, there is no paper in the printer’s cassette. If there was no

paper in the optional cassette, both the MANUAL/LGL and CASSETTE/

OTHERS indicators would flash. If there were no paper in the manual feed

tray the MANUAL/LGL indicator would flash.)

The cassette is not closed securely.

Close it tightly.

(Continued on next page)

Summary of Contents for FS-600

















































































































































Search results

Summary of Contents for FS-600

Reviews:

Related manuals for FS-600

Brands by name

Popular brands

Kyocera FS-600, User Manual

Search results

Summary of Contents for FS-600

Reviews:

Related manuals for FS-600

Brands by name

Popular brands