Kyocera FS-600 User Manual Download Page 82

Page: 82 / 144

Toner Container Replacement

4-2

Toner Container Replacement

When the printer runs low on toner, TONER indicator flashes on the control panel. Be sure to

promptly replace with a new toner kit and clean the inside of the printer when this initial message

appears.

If the printer stops printing while TONER indicator is lighting, replace with a new toner kit so the printer

can continue printing.

Toner Container Replacement Interval

Assuming an average toner coverage of 5% with Ecoprint mode turned off, the toner container will

need replacing approximately once every 3,000 printed pages.

Toner Kit to be Used

Name: TK-16

Description: Toner Container

Cleaning Cloth

Cap For Old Toner Container

Plastic Waste Bag (The toner kit supplied with the printer does not contain a plastic

waste bag.)

Instruction Manual

Summary of Contents for FS-600

















































































































































Search results

Summary of Contents for FS-600

Reviews:

Related manuals for FS-600

Brands by name

Popular brands

Kyocera FS-600, User Manual

Search results

Summary of Contents for FS-600

Reviews:

Related manuals for FS-600

Brands by name

Popular brands