Kyocera FS-600 User Manual Download Page 16

Page: 16 / 144

Introduction

Disclaimer

We shall have no liability or responsibility to customers or any other person or entity with respect to

any liability, loss or damage caused or alleged to be caused directly or indirectly by equipment sold or

furnished by us, including but not limited to, any interruption of service, loss of business or anticipatory

profits, or consequential damages resulting from the use or operation of the equipment or software.

Prolonged Non-Use and Moving the Printer

Prolonged Non-use

If you ever leave the printer unused for a long period of time, remove the power cord from the wall

outlet.

We recommend you consult with your dealer about the additional actions you should take to avoid

possible damages that may occur when the printer is used next time.

Moving the Printer

When you move the printer:

•

Move it gently.

•

Keep it as level as possible, to avoid spilling toner inside the printer.

•

If you ship the printer, remove and ship the process unit separately. Pack the process unit in a

plastic bag and ship them separate from the printer itself. Be sure to consult a serviceman before

attempting long-distance transportation of the printer.

Summary of Contents for FS-600

















































































































































Search results

Summary of Contents for FS-600

Reviews:

Related manuals for FS-600

Brands by name

Popular brands

Kyocera FS-600, User Manual

Search results

Summary of Contents for FS-600

Reviews:

Related manuals for FS-600

Brands by name

Popular brands