Kyocera FS-600 User Manual Download Page 28

Page: 28 / 144

Environmental Requirements of the Page Printer

1- 6

Basic handling precautions

Removing or changing parts other than disposable parts is prohibited. For repairs, contact the

Kyocera dealer from which you purchased the printer.

When moving the printer to a new location, contact the Kyocera dealer from which you purchased the

printer.

Using this printer to print currency or negotiable bonds is in violation of the law.

Unpacking and Inspection

Remove the printer from the package according to the steps given below. After removing the printer,

check that nothing is missing against the list of packaged contents.

Place the box containing the printer on a flat, stable surface.

Remove the

User’s

Manual, Toner Kit and other items located on top of the spacer and remove

the spacer.

Carefully remove the printer.

Summary of Contents for FS-600

















































































































































Search results

Summary of Contents for FS-600

Reviews:

Related manuals for FS-600

Brands by name

Popular brands

Kyocera FS-600, User Manual

Search results

Summary of Contents for FS-600

Reviews:

Related manuals for FS-600

Brands by name

Popular brands