Disk Mode
Load Function Dialog
13-21
Multiple Selection of Files to Load
As stated previously, you can select multiple Þles for loading into the K2vx from within a single
directory, in one operation. This is done from the Þle list dialog with the
Select
button.
After you have selected one or more Þles in this way, you will still choose a bank and mode to
be used for the load process, just as with loading a single Þle. However, the dialog prompt will
say "Load selected as":
||||||||||||||||||||||||||||||||||||||||
||||||||||||||||||||||||||||||||||||||||
||||||||||||||||||||||||||||||||||||||||
|||Load|selected|as:
200...299*
||||||||||
||||||||||||||||||||300...399|||||||||||
||||||||||||||||||||400...499*||||||||||
||||||||||||||||||||500...59
9||||
|
||||||
||||||||||||||||||||||||||||
|OK||
|
Cancel
If you selected any macro Þles (.MAC extension) from the directory, then once you have select
the mode for loading, you will see the question:
||||||||||||||||||||||||||||||||||||||||
||||||||||||||||||||||||||||||||||||||||
||||||||||||||||||||||||||||||||||||||||
Load|macros|as|specified?|||||||||||||||
||||||||||||||||||||||||||||||||||||||||
||||||||||||||||||||||||||||||||||||||||
||||||||||||||||||||||||||||
||||||
|
|||||
||||||||||||||||||||||||||||
|Yes||
|
|No||
The answer to this question instructs the K2vx that any macro Þles will have their macro entries
loaded according to the bank and mode:
Yes
speciÞed in the macro entry.
No
currently speciÞed for this multiple Þle load. In other words, whatever you select for Bank
and Mode will override the instructions for each entry in the macro.
At this point the Þles will begin to load. When all the Þles have been successfully loaded or the
load process has been aborted, the K2vx returns to the Disk Mode page.
If there are any errors encountered during a multiple Þle load, such as running out of object
RAM, you will be asked once if you wish to abort the load. In some cases, you may wish to
continue loading. If you continue (and don't abort), the only way to abort will be to use a
special procedure described in the next paragraph.
Aborting a Multiple File Load
There is a way to abort the process of loading multiple Þles. Aborting can only be done "in
between" Þles that are being loaded, and not during the load of any one Þle (short of powering
off or soft-resetting the machine by pr/-, 0, and CLR simultaneously, but this is not
recommended!).
Aborting a multiple Þle load is done by pressing and holding down either of the Plus (+) or the
Minus (-) buttons that are located just below the Alpha wheel. This should be done at least one-
half second before you anticipate the current Þle to Þnish loading, or else the K2vx will not
sense that you wish to abort the load.
Summary of Contents for K2500RS
