Konica Minolta Magicolor 5440 dl User Manual Download Page 139

Page: 139 / 164

Status, Error, and Service Messages

129

TRANSFER END

The transfer belt unit
has reached the end
of its life.

Replace the transfer belt
unit and reset the
counter in the

ENGINE/

SERVICE/RESET
COUNTER TRANS-
FER UNIT

menu.

TRANSFER LOW

The transfer belt unit
is near the end of its
life.

Prepare a new transfer
belt unit.

TRANS.ROLLER END

The transfer roller has
reached the end of its
life.

Replace the transfer
roller and reset the
counter in the

ENGINE/

SERVICE/RESET
COUNTER TRANS-
FER ROLLER

menu.

TRANS.ROLLER LOW

The transfer roller is
near the end of its life.

Prepare a new transfer
roller.

TRAY

EMPTY

Tray

(Tray 1, 2, or

3) was specified with
the printer driver for
printing, but Tray

empty.

Load media into the
specified tray.

UNSUPPORTED DIMM

An unsupported
DIMM is installed.

Check the DIMM specifi-
cations and install a sup-
ported DIMM.

WASTE:NEAR FULL

The waste toner bot-
tle is nearly full.

Prepare a new waste
toner bottle.

This message...

means...

do this...

Summary of Contents for Magicolor 5440 dl





































































































































































Search results

Summary of Contents for Magicolor 5440 dl

Reviews:

Related manuals for Magicolor 5440 dl

Brands by name

Popular brands

Konica Minolta Magicolor 5440 dl, User Manual

Search results

Summary of Contents for Magicolor 5440 dl

Reviews:

Related manuals for Magicolor 5440 dl

Brands by name

Popular brands