Konica Minolta Magicolor 5440 dl Page 142 User Manual Download

Page: 142 / 164

Status, Error, and Service Messages

132

PUT MEDIA : M-TRAY
“SIZE”

The media size set in
the printer driver is
different from the size
of media loaded.

Load the correct media
size into the manual
feed tray.

PUT MEDIA : TRAY

“SIZE”

The media size set in
the printer driver is
different from the size
of media loaded.

Load the correct media
size into the specified
tray.

REPLACE TONER

The

toner cartridge

is empty
(Appears when

ENGINE/TONER
EMPTY STOP

is set).

Replace the toner car-
tridge.

SIZE/TYPE ERROR

Unsupported media
(wrong size, thick-
ness, type, etc.) is
being used.

Load the correct media
size and type.

SIZE/TYPE ERROR
DUPLEX

The media not com-
patible with duplex
printing.

Use the correct media
size and type when
duplexing.

TONER LIFE END

The

toner cartridge

is completely empty.
(Appears when

ENGINE/TONER
EMPTY CONTINUE

is set)

Replace the toner car-
tridge.

TONER

NOT INSTALLED

The

toner cartridge

is not installed, or an
unapproved toner
cartridge is installed.

Install a correct KONICA
MINOLTA toner car-
tridge.

TRAY

NOT ATTACHED

Tray

(Tray 2 or 3)

was specified with the
printer driver for print-
ing, but Tray

is not

installed.

Stop the print job and
change the printer driver
setting. If necessary,
install Tray

WASTE BOTTLE FULL

The waste toner
bottle is full.

Install a new waste toner
bottle.

This message...

means...

do this...

Summary of Contents for Magicolor 5440 dl





































































































































































Search results

Summary of Contents for Magicolor 5440 dl

Reviews:

Related manuals for Magicolor 5440 dl

Brands by name

Popular brands

Konica Minolta Magicolor 5440 dl, User Manual

Search results

Summary of Contents for Magicolor 5440 dl

Reviews:

Related manuals for Magicolor 5440 dl

Brands by name

Popular brands