Knick Protos LDO 3400-170 User Manual Download Page 54

Page: 54 / 64

Specifications

General data

This equipment is not designed for domestic use, and is unable to guarantee adequate

protection of the radio reception in such environments.

RoHS conformity

According to EU directive 2011/65/EU

EMC

Emitted interference
Interference immunity

EN 61326-1, EN 61326-2-3
NAMUR NE 21
Industrial applications* (EN 55011 Group 1 Class A)
Industrial applications

Lightning protection

to EN 61000-4-5, Installation class 2

Rated operating conditions

Ambient temperature:
-20 ... 55 °C / -4 ... 131 °F
Relative humidity: 10 ... 95 % non-condensing

Transport/storage
temperature

-20 ... 70 °C / -4 ... 158 °F

Screw clamp connector

Single or stranded wires up to 2.5 mm2

Summary of Contents for Protos LDO 3400-170

































































Search results

Summary of Contents for Protos LDO 3400-170

Reviews:

Related manuals for Protos LDO 3400-170

Brands by name

Popular brands

Knick Protos LDO 3400-170, User Manual

Search results

Summary of Contents for Protos LDO 3400-170

Reviews:

Related manuals for Protos LDO 3400-170

Brands by name

Popular brands