Knick Protos LDO 3400-170 User Manual Download Page 5

Page: 5 / 64

Intended Use

NOTICE!

Potential damage

Never try to open the module. Protos modules cannot be repaired by the

user. For inquiries regarding module repair, please contact Knick Elektronische

Messgeräte GmbH & Co. KG at www.knick.de.

Be sure to observe during installation:

• Switch off power supply before replacing or inserting a module.

• Protect the signal inputs of the modules against electrostatic discharge.

• Before commissioning it must be proved that the device may be connected

with other equipment.

Safety Information

The module is used to measure oxygen in liquids and gases using an SE 740

series optical sensor. It measures the partial pressure of oxygen, air pressure,

and temperature simultaneously. It is also able to calculate and display the oxy-

gen saturation and concentration as well as volume concentration in gases.

The LDO 3400-170 / LDO 4400-170 module is not intended for operation in

locations subject to explosion hazards.

Summary of Contents for Protos LDO 3400-170

































































Search results

Summary of Contents for Protos LDO 3400-170

Reviews:

Related manuals for Protos LDO 3400-170

Brands by name

Popular brands

Knick Protos LDO 3400-170, User Manual

Search results

Summary of Contents for Protos LDO 3400-170

Reviews:

Related manuals for Protos LDO 3400-170

Brands by name

Popular brands