Knick Protos LDO 3400-170 User Manual Download Page 10

Page: 10 / 64

Adjustment:

The sensor adjusts itself. Adjustment is started and monitored via Protos.

Calibration / Adjustment

Note:

The function check (HOLD) mode is active for the currently calibrated

module, the current outputs behave as configured.

NOTICE!

Without adjustment every oxygen meter delivers an imprecise or wrong output

value! After replacing the sensor or the sensor membrane, you must perform an

adjustment.

Procedure

Every oxygen sensor has its individual slope (Stern-Volmer constant cvs) and

its individual zero point (phase angle). Both values are altered, for example, by

aging.

For sufficiently high accuracy of oxygen measurement, the analyzer must be

regularly adjusted for the sensor data (adjustment).

Calibration/Adjustment Methods

• Automatic calibration in water/air

• Product calibration (saturation/concentration/partial pressure)

• Zero correction

Summary of Contents for Protos LDO 3400-170

































































Search results

Summary of Contents for Protos LDO 3400-170

Reviews:

Related manuals for Protos LDO 3400-170

Brands by name

Popular brands

Knick Protos LDO 3400-170, User Manual

Search results

Summary of Contents for Protos LDO 3400-170

Reviews:

Related manuals for Protos LDO 3400-170

Brands by name

Popular brands