Knick Protos LDO 3400-170 User Manual Download Page 43

Page: 43 / 64

Set/delete favorite:

“Set favorite” allows activation of the

selected diagnostic function directly

from the measuring mode via softkey.

The menu line is marked with a heart

icon.

Pressing the

meas

key returns to

measurement. When the softkey has

been assigned to “Favorites”, “Favorites

menu” is read in the secondary display

(see “Function control matrix”).

Note:

When one of the softkeys has been assigned to the “Favorites menu” function,

diagnostic functions which have been set as “Favorite” can be directly called

from the measuring mode.

Menu Display

Selecting a favorite

Favorites Menu

Diagnostics functions can be called

directly from the measuring mode

using a softkey.

The “Favorites” are selected in the

Diagnostics menu.

Selecting a Favorite

Press

menu

key to select menu.

Select Diagnostics using arrow keys,

press

enter

to confirm.

Then select the module and

confirm by pressing

enter

03/09/14

Favorites menu

03/09/14

Favorites menu

Menu selection

Return to meas

83.3 %Air

25.6°C

Select:

[enter]

Lingua

Set favorite

Sensor SE 740

Return

23.0 °C

83.3 %Air

Cal record

Sensor diagram OXY

Sensor wear monitor

Sensor monitor

he displa

y ma

y v

y depending on the devic

e v

ersion.

Summary of Contents for Protos LDO 3400-170

































































Search results

Summary of Contents for Protos LDO 3400-170

Reviews:

Related manuals for Protos LDO 3400-170

Brands by name

Popular brands

Knick Protos LDO 3400-170, User Manual

Search results

Summary of Contents for Protos LDO 3400-170

Reviews:

Related manuals for Protos LDO 3400-170

Brands by name

Popular brands