28
EN
6.2 - Programming the pedestrian
(partial) opening width
This procedure allows to change the default pedestrian opening
gap.
Default opening settings:
- swing gates: Motor 1 fully open
- sliding gate: 30% of the total travel
To control the pedestrian opening, it is necessary to either
programme a radio control button (see Paragraph 5.2) or connect
a wired control device on the PED contact (see Paragraph 3.2).
m
Prior to proceeding with this programming procedure,
make sure that either basic programming or advance
programming of the gate travel have been completed.
1.
CLOSE THE GATE FULLY
2.
PRESS THE
SET
BUTTON FOR 2 SECONDS: the
SET
led
flashes (if not, consult Paragraph 17.1)
3.
PRESS THE
START
BUTTON FOR 1 SECOND: the
SET
led
turns ON
4.
THE GATE STARTS TO OPEN: the
SET
led stays ON
5.
PRESS THE
START
BUTTON OR A PROGRAMMED
TRANSMITTER BUTTON: the
SET
led stays ON
6.
THE GATE STOPS THE MANEUVER AND CLOSES FULLY:
the
SET
led turns OFF
7.
END OF THE PROGRAMMING PROCEDURE: the LEDs
return to the normal operation configuration
6.3 - Advanced programming of the
gate travel
With this procedure, you will set the slow down points or remove
them completely.
1.
PUT THE GATE LEAF/LEAVES TO TO ABOUT HALF WAY
POSITION
2.
PRESS THE
SET
BUTTON FOR 2 SECONDS: the
SET
led
flashes (if not, consult Paragraph 17.1)
3.
PRESS THE
RADIO
BUTTON FOR 1 SECOND: the
SET
led
turns ON in the fixed mode
4.
THE GATE PARTIALLY OPENS: the
SET
led flashes
5.
THE SYSTEMS PAUSES
FOR APPROX 8 SECONDS (*)
6.
THE GATE MOVES TO FULL CLOSING POSITION: the
SET
led stays ON
7.
PRESS THE
SET
BUTTON OR A PROGRAMMED
TRANSMITTER BUTTON
8.
THE GATE OPENS
9.
PRESS THE
SET
BUTTON, OR A PROGRAMMED
TRANSMITTER BUTTON, TO
SET
THE SLOWDOWN
START
POINT. TO CANCEL THE SLOWDOWN POINT, JUST WAIT
FOR THE GATE TO FINISH THE MANOUVER
10.
THE GATE COMPLETES THE OPENING PHASE
11.
PRESS THE
SET
BUTTON OR A PROGRAMMED
TRANSMITTER BUTTON
12.
THE GATE CLOSES
13.
DURING MOVEMENT: PRESS THE
SET
BUTTON OR A
PROGRAMMED TRANSMITTER BUTTON TO
SET
THE
SLOWDOWN
START
POINT. TO CANCEL THE SLOWDOWN
POINT, JUST WAIT FOR THE GATE TO FINISH THE
MANOUVER
14.
THE GATE IS NOW FULLY CLOSED: the
SET
led turns OFF
m
With double hinged gate, the control unit will open
and close one leaf at a time.
m
After any POWER knob adjustment, the gate travel
learning must be reprogrammed.
m
If the operator does not recognise the mechanical
stops (end of the travel for swing gates) even with the
OBS knob set to its minimum, you can select the open and
closed points during programming by pressing the SET
button (or a programmed transmitter’s button) at the end of
points 6, 9 and 13. In the event of two gate leaves, use the
SET button for both leaves.
(*) Procedure 1: REVERSING THE DIRECTION OF THE GATE
SECTION 1 (MOTOR 1) OPENING STROKE
1.
PRESS THE
RADIO
BUTTON FOR 3 SECONDS: the
SET
led
flashes fast
2.
LEAF 1 MOVES TO VERIFY THAT THE MOTOR OPENS: the
SET
led flashes
3.
THE CONTROL UNIT RETURNS TO STAND-BY MODE FOR
8 SECONDS (Point 5 of the programming sequence): the
SET
led flashes
(*) Procedure 2: REVERSING THE DIRECTION OF THE GATE
SECTION 2 (MOTOR 2) OPENING STROKE
1.
PRESS THE
RADIO
BUTTON FOR 3 SECONDS: the
SET
led
flashes fast
2.
LEAF 2 MOVES TO VERIFY THAT THE MOTOR OPENS: the
SET
led flashes
3.
THE CONTROL UNIT RETURNS TO STAND-BY MODE FOR
8 SECONDS (Point 5 of the programming sequence): the
SET
led flashes
Summary of Contents for STARG8 24NG
Page 111: ......
