Keysight Technologies N9010A Series Installation Note Download Page 3

Page: 3 / 63

Installation Note N9010-90054

Option HL4, 40 MHz Analysis Bandwidth (B40) + Microwave Preselector Bypass (MPB) Upgrade Kit

Option HL4, 40 MHz Analysis Bandwidth (B40) + Microwave

Preselector Bypass (MPB) Upgrade Kit

Software and test equipment is required for making adjustments and for performance verification

testing.
Information on how to obtain this software can be found at:

www.keysight.com/find/calibrationsoftware

While Keysight does recommend that a full calibration be performed after the installation of this

upgrade, the end user must ultimately determine whether they want this service or not. If a full

calibration is required, arrangements regarding the level of calibration must be made between the

end user and the calibration provider.

Products Affected:

N9010A, EXA Signal Analyzer

N9020A, MXA Signal Analyzer

Serial Numbers:

N9010A,

MY/SG/US56480000

N9020A,

MY/SG/US52330000

Options: B40,

MPB

To Be Performed By:

(X) Keysight Service Center

(X) Personnel Qualified by Keysight

( ) Customer

a. To ensure that these newly installed options are functioning properly, the procedure that follows

includes the requirement of performing certain adjustments and performance verification tests.

However, the completion of these tests does not guarantee that the instrument meets all advertised

specifications.

Estimated Installation Time:

Estimated Adjustment Time:

Estimated Verification Time:

3.0 Hours

5.5 Hours

3.5 Hours

Summary of Contents for N9010A Series
































































Search results

Summary of Contents for N9010A Series

Reviews:

Related manuals for N9010A Series

Brands by name

Popular brands

Keysight Technologies N9010A Series, Installation Note

Search results

Summary of Contents for N9010A Series

Reviews:

Related manuals for N9010A Series

Brands by name

Popular brands