Keysight Technologies N9010A Series Installation Note Download Page 49 | Manualshive

Page: 49 / 63

background image

Installation Note N9010-90054

49

Installation Procedure

13.

Refer to

. Locate W38 in the Opt HL4 Cable Kit. This cable will have part number

8121-1861 and will be labeled “901” on one end and “15” on the other. Connect the end

labeled “901” to A15J901 on the A15 Enhanced Front End Controller (EFEC) Assembly. Route

the cable along the side of the EFEC board to the right side of the instrument and through the

cutout in the chassis between A9 and A12. Connect the other end to A3J15 on the A3 DIF

Assembly.

Figure 36

W36, W37, W38, and W39 Cables

14.

Refer to

. Disconnect W15 from A13J7 of the A13 RF Front End Assembly and remove

the cable; it will not be used.

15.

Refer to

. Locate W36 in the Opt HL4 Cable Kit. This cable will have

part number 8121-1862 and will be labeled “902” on one end and “7” on the other. Connect

the end labeled “902” to A15J902 on the A15 EFEC Assembly. Connect the other end to A13J7

on the A13 Front End Assembly. Torque the connector on A13J7 to 10 inch-pounds.

«
...
47
48
49
50
51
...
»

Summary of Contents for N9010A Series
































































Reviews:

No comments

Related manuals for N9010A Series

DigitalFlow XMT868i

Brand: Panametrics Pages: 74

Brand: 4iiii Pages: 3

Brand: Sabre Pages: 13

Brand: A&D Pages: 39

Wind Monitor Series

Brand: Campbell Pages: 38

Brand: Favero Electronics Pages: 12

Brand: Danfoss Pages: 80

Brand: Schneeberger Pages: 35

Brand: Chroma Pages: 63

Ranger TDR VDV501-090

Brand: Klein Tools Pages: 44

Brand: PRONIVO Pages: 40

Brand: socomec Pages: 34

Brand: Trotec Pages: 14

Brand: PCB Piezotronics Pages: 16

fieldscout TDR 100

Brand: Spectrum Techniques Pages: 20

Brand: Van Walt Pages: 2

Brand: Konica Minolta Pages: 92

Brand: Tektronix Pages: 116

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands