manualshive.com logo in svg

Keysight Technologies N9010A Series, Installation Note

Share
Download
Keysight Technologies N9010A Series Installation Note Download Page 12

12

Installation Note N9010-90054

Installation Procedure

7.

The signal analyzer will automatically consume the License File. (This may take a few minutes) 

When the License File is consumed the Keysight License Manager will display a “Successful 

License Installation” message as shown in 

Figure 2

. Since the license file contains multiple 

licenses, multiple “Successful License Installation” messages will appear. Wait until all 
licenses have been consumed before removing the USB Storage Device.

Figure 2 

Successful License Installation

If you will also be installing any of the following upgrade products:

N90x0AK-CR3, 2nd IF Output
N90x0AK-CRP, Arbitrary IF Output
N9010AK-P07, Preamplifier, 7 GHz

now would be the best time to install the licenses for these other upgrades, By installing the 

licenses now, the adjustments and performance verifications for these other upgrades will also 

be performed.

Summary of Contents for N9010A Series
































































Reviews:

No comments

Brands by name

Popular brands

Load more brands